Dragon Force(Shenzhen) Energy Euipment Co.,Ltd&Shengzhen Guanruixing Manufacturing Equipment Co.,Ltd
High pressure reciprocating natural gas compressor
Suitable for offshore applications, for gas treatment of offshore platforms and FPSO.
Category:
-
Main features of Guanruida high-pressure reciprocating screw compressor series
1. Direct drive, no gears, higher reliability
1). Avoid the possibility of failure caused by gear wear and increase reliability;
2). Reduce vibration and noise;
3). Higher transmission efficiency;
4). Reduce the power consumption generated by the gear part;
5). Reduce the lubricating oil consumed on the gears, and at the same time increase the life of the lubricating oil.
2. The bearing is arranged in a special way and the force is better
1). Roller bearings are used to bear radial loads;
2). Tapered roller bearings bear axial and radial forces;
3). No start-up pre-lubrication requirements.
3. Balance piston (reduce bearing stress)
The balance piston is installed on the two rotors. Under the action of pressure, oil enters the piston to produce a force that partially offsets the thrust load. This will reduce the thrust acting on the thrust bearing, and the bearing life will be longer.
4. Long service life of screw main engine
U.S. Sullair process gas special screw main engine has been deeply cultivated in the field of special compressors for decades. After continuous improvement and innovation, the performance is far better than similar screw main engines of other brands. Practice has proved that the Sullair screw main engine has superior performance and good reliability, and the service life of the main engine is more than 80,000 hours.
5. The screw host adopts a mechanical seal with zero leakage
The Sullair screw main engine of the United States is optimized for high-pressure working conditions. The John Crane mechanical seal with reliable performance and two-stage seal structure is selected to ensure that the shaft seal of the screw main engine has zero leakage and no oil and natural gas overflow the compressor.
1) The first stage is a labyrinth seal structure with reverse thread. If oil enters the shaft seal, this reverse thread will pump the oil back into the compressor;
2) The second level is a high temperature resistant and hardened graphite sealing structure, and it has a good sealing effect with tungsten surface and fluorine rubber elastomer.
6. High exhaust pressure
Guanruida's natural gas screw compressor has a maximum discharge pressure of 507psig (3.5Mpag), which is currently the world's highest technology for screw compressors.
7. Advanced purification design
At present, the natural gas compressor on the market needs to be equipped with additional natural gas pretreatment equipment before use to ensure that the gas source enters the compressor without impurities, while the user of Guanruida natural gas screw compressor does not need to configure a purification device, and can directly connect to the wellhead of the oil well. Perform compression work.
8. Environmentally friendly design
Guanruida natural gas screw compressor originated from the United States, and pays special attention to environmental protection. It automatically recovers impurities and special treatment, and the body is in harmony with nature.
9. Satellite remote control
The natural gas screw compressor can be equipped with PLC to realize remote remote control by satellite. At the same time, it uses the solar energy and wind energy on site to transmit signals to the remote base station, which can realize completely unattended and remote control operation under extremely harsh conditions.
Main performance parameters of high-pressure reciprocating natural gas compressorModel
Main parametersGS604-211 GS604
-212GS604
-213GS60
4-313GS60
4-314GS604
-316GS604
-319GS604
-320GS604
-428GS604
-427Inlet pressure (Mpag)
Suction Pressure1. 9--4. 9 1. 9
--3. 41. 6
--2. 71. 0
--1. 91. 0
--1. 50. 6
--1. 23. 5
--7. 03. 5
--5. 51. 5
--4. 50. 5
--2. 0Flow Max. (Nm³/H)
Delivery8098 6750 5690 4840 4584 4364 3640 3476 3327 2566 Power requirement (Kw)
Max.588 590 582 562 560 560 572 574 590 574 Motor power (Kw)
Motor630 630 630 560 560 560 630 630 630 630 Dimensions (mm)
Dimensions5125X3000
X25915125X3000
X25915125X3000
X25915125X3000
X25915125X3000
X25915125X3000
X25915125X3000
X25915125X3000
X25915125X3000
X25915125X3000
X2591Weight (KG)
Weight16000 16000 16000 18000 18000 18000 18000 18000 20000 20000
Keywords:
Recommended products
Dragon Force(Shenzhen) Energy Euipment Co.,Ltd